• 3.33 Gallon Units
  • High gloss finish
  • High wear resistance / durable
  • Manufactured in WATER CLEAR, but able to be colored using ROCK-TRED Universal Colorants
  • Cures down to 50° F
  • Excellent weathering and UV resistance
  • Exceptional color retention
  • Indoor / outdoor coating

Description

ELASTI-THANE LINE STRIPING (V.2012) is a high solids, two-component, WATER CLEAR, aliphatic polyurethane coating intended for line striping and marking over primed surfaces or other ELASTI-THANE systems. ELASTI-THANE LINE STRIPING (V.2012) is manufactured in WATER CLEAR, but is able to be field pigmented using ROCK-TRED Universal Colorants. This product provides exceptional gloss and color retention even in UV exposed areas and under heavy wear. ELASTI-THANE LINE STRIPING (V.2012) is a tough and durable coating that is impervious to water, chloride penetration and most common automotive chemicals.

 

Uses

ELASTI-THANE LINE STRIPING (V.2012) is ideal for striping gym floors, tennis courts, play areas and ELASTI-THANE System coated parking decks. This product can be applied at temperatures down to 50° F

 

Typical Coverage

ELASTI-THANE LINE STRIPING (V.2012) is typically applied at approximately 200 square feet per gallon and may require two coats to achieve full hide depending on color and surface texture.

 

Physical Properites

Volume mix ratio Mix Entire Kit
Viscosity (mixed) 2,000 – 3,000 CPS
Solids Content (%) 42% (ASTM D-2697)
Ultimate Elongation (ASTM D412) 70 %
VOC Content 580 – 600 g/l (EPA method 24)
Application Temps. 50° - 95° F
Gel Time 40-50 minutes @ 75° F
Dry to Touch (recoat withcompatible products) 8 - 10 hours @ 75° F
Through Cure 9 - 11 hours @ 75° F
Open for light traffic 24 hours @ 75° F
Shelf Life 1 year in unopened units
 

Limitations & For Best Results

  • Do not thin this product.
  • Apply product between 40% - 90% relative humidity. Do not apply when substrate temperatures may fall to less than 5° F above the Dew point during the curing of the material.
  • When re-coating, always apply the next coat within 24 hours of completing the previous coat.
  • Do not apply this product heavier / thicker than the recommended spread rate / mil thickness.
  • Power mix for a minimum of 5 minutes at low RPM using a Jiffy Mixer – do not entrain air.
 

 

 

Product Application

 

Apply using brush, roller and squeegee. ROCK-TRED product test data is based on environmental temperatures of 75° F. Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.

 

Color and Textures

ELASTI-THANE LINE STRIPING (V.2012) is manufactured in WATER CLEAR and can be field pigmented using ROCK-TRED colorants at a ratio of 1 full Bag Pak Colorant per 3.33 gallon mixed unit. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.

 

Chemical Resistance

Always refer to ROCK-TRED’s chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.

 

Product Storage

DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50° F (10° C).

 

Surface Preparation

Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooringsystems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shot-blasting or diamond grinding machine to a minimum CSP-2 profile followed by priming or installation of compatible base coatings is the best and recommended preparation method for ELASTI-THANE LINE STRIPING (V.2012) applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.

 

Clean Up

Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.

 

Disposal

Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.

 

Important Notice

Always read and acquaint yourself with ROCK-TRED’S Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.