Chem-Rock Safety-Tred

Available Sizes
  • 1 gallon units
  • 5 gallon units
Advantages
  • Heavy duty, long lasting, uniform, non-skid finish without broadcasting
  • Indoor/outdoor use
  • May be applied at temperatures from 50° – 120°F
  • VOC compliant
  • Good abrasion and chemical resistance
  • Easy to apply uniformly
  • Dry service temperatures up to 160°F

Description

CHEM-ROCK SAFETY-TRED is a high solids, low odor, solid color, 2-component, aggregate filled, 92% solids epoxy coating formulated for interior or exterior applications where an anti-slip finish profile is required. CHEM-ROCK SAFETY-TRED has good resistance to automotive fluids and many common chemicals found in food/beverage and general manufacturing. It is VOC/HAPS compliant and meets USDA/FDA guidelines for use in federally-inspected facilities.

 

Uses

CHEM-ROCK SAFETY-TRED is used as a heavy duty, long-wearing, non-skid epoxy coating for industrial and marine applications. With an appropriate primer it can be applied over both concrete and metal surfaces.

 

Typical Coverage

CHEM-ROCK SAFETY-TRED is typically applied at 30 - 50 square feet per gallon per coat depending upon substrate and project requirements.

 

Physical Properites

Volume mix ratio 4 to 1 (Resin to Hardener)
Solids Content (%) 92% (ASTM D-2697)
VOC 74 g/l (EPA method 24)
Application Temps. 50° – 120°F
Gel Time 60 minutes @ 75° F
Dry to Touch (recoat with compatible products) 12 hours @ 75°F
Gel Time 3 – 4 hours @ 75° F
Dry to Touch (recoat with similar product) 8 hours @ 75° F
Through Cure 24 hours @ 75°F
Open for light traffic 24 - 36 hours @ 75°F
Open for heavy traffic 36 - 48 hours @ 75°F
Shelf Life 1 Year in unopened units
 

Limitations & For Best Results

  • Do not apply when humidity exceeds 70% indoors or when the temperature is within 5° of Dew Point.
  • Do not allow to puddle during application.
  • Allow each coat to dry to 'tack-free' prior to re-coat.
  • When re-coating, always apply the next coat within 24 hours of completing the previous coat.
  • This is a relatively slow curing product. Be sure to allow enough cure time prior to opening coated area for use or before recoating.
  • Always use an appropriate ROCK-TRED primer under this coating.
  • May be used outdoors, but loss of gloss will occur over time when exposed to the elements.
  • Do not over roll material as this can decrease the non-skid finish.
 

Product Application

CHEM-ROCK SAFETY-TRED should be applied with a phenolic core roller, squeegee, or trowel. A phenolic core roller cover (smooth, phenolic resin coated roller tube without any nap) will produce a uniform ridged surface. If a smoother surface is desired, use a trowel or a flat blade squeegee. Immediately after mixing pour a ribbon onto surface. The ribbon should be approximately 2-3 feet long and 6" wide. When using a roller pull the material towards you using some pressure. Roll material only in one direction. Strike off any excessive material build-up on edges from roller lap. When using a squeegee or trowel, hold on 45° angle pulling material toward you. ROCK-TRED product test data is based on environmental temperatures of 75°F. Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.

 

Colors

CHEM-ROCK SAFETY-TRED is manufactured in Gun Powder Gray and Safety Yellow.

 

Chemical Resistance

Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.

 

Product Storage

DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.

 

Surface Preparation

Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shot-blasting or diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer is the best and recommended installation method for CHEM-ROCK SAFETY-TRED applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.

 

Clean Up

Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.

 

Disposal

Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.

 

Important Notice

Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids all warranties.